CNC Router Studio

G-code for hobby routers, written in your browser. Your original picture never leaves this computer. There is no queue and nothing to wait for.

New here? Read the CNC Router Studio User Guide (or the PDF)

A router throws chips, and a cutter that breaks throws pieces of itself. Goggles and ears, work clamped down and not held, sleeves and hair out of the way, and your hand nowhere near the cutter while the spindle turns. Air-cut the file first — zero Z well above the work, run the whole job in the air, and watch it. Then check the Z zero again before you cut for real. Look at the toolpath preview before you send anything, and start with a shallow depth of cut: a setting that suits one machine and one piece of wood is wrong for the next.
A dog carved as a relief in wood, with a ball-nose bit above it Photo to carved relief A picture carved into wood: a roughing pass to take the waste out in layers, then a ball-nose pass over the surface. The preview shows the surface your cutter will really leave, not the one you asked for. It is the only way to find out before you cut that the bit is too big. A block of wood with a pocket being cut in a 3D simulation 3D simulator free Cut the file into a block of wood on screen and turn it round, before a cutter does it for real. It reads the finished file rather than the plan that made it, so it can catch the writer out, and it takes any GRBL file, not only the ones made here. A desktop CNC router cutting plywood, connected to a laptop by USB Send to machine free Run the file on your router from the browser: connect over USB, jog, set the zero, frame the job and cut, with a stop at every cutter change. Chrome or Edge on a computer, nothing to install. Try it first with the simulated machine. Shapes drawn on screen next to the same shapes cut from plywood 2D designer new Draw lines, rectangles and circles over a photo, or type text as outlines, then pick the bit and cut it through or engrave it: material thickness, depth, passes and tabs. The G-code goes straight to your machine. A simple circuit board layout with a chip, parts and copper lines PCB designer new Draw a simple circuit board: resistors, LEDs, transistors, chips, switches and connectors, joined with copper lines. Drag them where you want them, then make the cut files in one click. A fine engraving bit milling the copper of a circuit board PCB to G-code new Mill a circuit board from the files KiCad or EasyEDA export: the isolation round the copper, the holes and the cut-out with tabs, with a warning wherever two tracks are too close for the bit. Use the height map on Send to machine for a board that is not quite flat. An end mill cutting a curved shape out of plywood Outline to profile cut and pockets Cut a shape out of the material or hollow one into it, from an SVG or a traced picture. Real tool radius offsetting rather than the approximate kind, the cut taken off in layers, a ramp into each pass, and tabs so the part is still there when the last cut finishes. A V-bit carving swirls into oak V-carved text and outlines The one that makes letters look cut rather than routed: the depth follows the width of each stroke, so a serif tapers away to nothing and every inside corner comes to a true point. Type the words, or bring a drawing. A wide surfacing bit flattening the top of a wooden board Flatten a piece new Take a board down to one level all over before you carve, cut or engrave it. Give it the size, how much to take off and the bit; it runs the whole piece in rows, in layers, and always goes down beside the piece, never into it.

i What these make, and what they do not

i If you have a laser as well

The same thing for laser engravers and cutters is its own studio, Laser Maker Studio: photo engraving, cutting from an SVG, a power and speed test grid, and a simulator that plays a GRBL file back move by move.

Setting a job up, the previews and the toolpath are free for everyone. Downloading G-code needs a free account: 10 free downloads a month (shared with the rest of the site) and no limit with CNC Router Studio, bought once, for life (it is not part of the Supporter plans). Log in or register, or see CNC Router Studio.