CAD — Help

Precise parts you can change later: every step stays editable, and sizes can be names

What it is (and when to use it)

CAD is the 3D Maker Studio tab for exact, functional parts. A part is a list of steps (sketch → extrude → hole → fillet …). The kernel (OpenCascade, the same one FreeCAD uses) rebuilds the exact shape from that list every time you change something.

For paid members (Supporter, Supporter Plus or the 3D Maker Studio unlock), on the website and in the desktop app. A free account can open the tab and look at every button; each one says "Only for paid members".

  • Change any step later and everything after it follows. Make the sketch 50 mm instead of 40 and the holes, fillets and patterns update.
  • Sizes can be names (wall = 2), used in many places.
  • True geometry: real circles, fillets and threads, and STEP export for other CAD programs and machine shops.

Use the Designer for gifts, figures, signs, lithophanes and remixing STLs. Use CAD for parts that must fit something (brackets, boxes with lids, enclosures, replacement parts, screw holes) or that you'll tweak several times. A CAD part sent to the Designer stays editable in CAD.


Quick start

  1. A new part opens with an empty sketch on the bed. Pick the rectangle or circle above the grid and drag. Type exact sizes on the right.
  2. Make it solid: Solid › Extrude. Type the height.
  3. Add a hole: Modify › Screw hole, then click the top face.
  4. Click any step in the list on the left and change a size: the whole part updates.
  5. Export › STL for your slicer, or Send to › Designer.

An empty part shows a Start here card. Open an example loads a plate whose width and hole are parameters: change one under Parameters and watch the plate and both holes follow.


The screen

  • Top bar: the part's name, and the File, Export, Send to, View and Help menus. Send to Designer is on the right.
  • Rail (far left): undo / redo, then Sketch, Solid, Modify and Measure. A click opens that group's tools beside it.
  • Left column: the feature list (the steps, top to bottom), Parameters and Measure (size, volume, weight, centre of mass).
  • Middle: the 3D view, or the sketch board while a sketch is selected ( 3D goes back to the view).
  • Right: the selected step's settings in exact mm. Every number has ▲ ▼ arrows (hold to repeat, Shift ×10, or Arrow Up / Down in the field). It can also hold an expression such as wall*2 + 1.
  • 3D view: drag to orbit, right-drag to pan, wheel to zoom. Click an object to select it (orange). Its arrows move it, and R switches to rings to turn it.

Sketch planes

  • Sketch › On XY (flat on the bed), On XZ (front) or On YZ (side).
  • Offset moves the plane along its normal, for example 20 mm up.
  • Tilt leans the plane about its own x axis. Turn spins it about its normal. Use them for sloped faces and angled features.
  • On a face of the part…: click any flat face. The sketch sits on it, and an Extrude grows out of it, or cuts into it with a minus distance or Cut.
  • The part's edges that lie on the plane show as faint lines on the board, so you can snap to them.

Drawing on the board

Rectangle (R): drag corner to corner.
Circle (C): drag from the centre.
Ellipse (E): drag from the centre to a corner of its box.
Polygon (P): drag from the centre to a corner (6 sides; change them on the right).
Slot (O): drag from one end's centre to the other.
Outline (L): click points. next: line / arc picks the next segment. Click the first point, or press Enter, to close it.
Text (T): raised or engraved letters. Type the text and its height on the right.
By size: Rectangle / Circle / Hexagon / Slot / Ellipse by size add one at 0,0 to type in.
  • Snap (top of the board) rounds points to 0.1 to 5 mm. Points also snap to corners, centres and the part's edges.
  • Edit: drag a shape to move it, and its small squares to resize it. On an outline, drag its points, and click a + to add one. Arrow keys nudge (Shift ×10). Delete removes the shape.
  • Right-click a shape or a point: copy, duplicate, flip, turn 90°, make it a construction line, round or chamfer this corner, make a line an arc, extend or trim an open end to the nearest line, turn a shape into an outline.
  • A shape inside another is cut out of it (a hole in a plate). Each shape can also be set to Add or Cut out.
  • Bring in a DXF or SVG drawing… (on the sketch's settings) turns lines, arcs, circles and curves into outlines.
  • Wheel zooms, and Shift-drag or right-drag pans. fits the view.

Shape settings

Select a shape (or the sketch) to see each shape's numbers on the right.

  • Round corners / Chamfer corners (rectangle, polygon, closed outline): every corner at once. Right-click one point to round just that corner.
  • Grow by: an offset of the outline, outwards (minus = inwards). Use it for a lip, a gasket groove or a clearance.
  • Smooth curve through the points (outlines): a spline instead of straight lines, for organic or flowing shapes. Drag the points to shape the curve.
  • Open (outlines): a line, not a shape. Sweep follows it. With a Wall thickness above 0 it becomes a wall you can extrude (ribs, brackets, thin walls).
  • Construction (right-click): drawn dashed and never built. Use it as a guide to snap and trim to.

Rules (constraints)

Rules keep a sketch the way you meant it when you change a number.

  1. Pick the Rules tool (K).
  2. Click a point, line or circle on the board, and a second one if the rule needs it.
  3. On the right, pick the rule.
Same point: two points join
Level / Upright: a line, or two points, horizontal / vertical
Distance: a line's length, or the gap between points or a line and a point
Radius: a circle or arc
Parallel / Square (90°): two lines
Same size: two lines or two circles
Fixed in place: it does not move
Touching (tangent) / On it: a line or circle meets a circle; a point lies on a line or circle

Rules show as small marks on the board. The box tells you how many ways the sketch can still move (0 = fully fixed). If a typed number can't fit the rules, the field turns red and keeps the last size that fits. Right-click a mark to delete its rule.


Solid: making a body

  • Extrude: the sketch above the selected step, pushed straight out.
    • Both ways centres it on the plane.
    • Draft leans the sides in by an angle (for moulds and overhang-free prints).
    • Shapes lets you extrude only some of the sketch's shapes.
    • A minus distance goes the other way.
  • Revolve: turns the sketch about its x or y axis (vases, knobs, wheels). The shape must stay on one side of that axis.
  • Loft: a solid through shapes on two or more sketches on different planes, for example a square at the bottom and a circle 30 mm up.
  • Sweep: a profile (drawn around its own 0,0) carried along a path (an open outline in another sketch). Use it for pipes, handles and rails.
  • Box / Cylinder: quick solids, placed beside the part. Type their size and position.
  • Gear: an involute spur gear from its module and number of teeth. Two gears mesh m·(z1+z2)/2 apart.
  • Snap-fit hook: a clip that catches. The note shows the strain, so you can keep it below what the plastic takes.
  • Bolt, threaded rod or nut: printable M2 to M12 threads with printing clearance.
  • Import a STEP or STL…: a model from a file, as a solid you can cut, add to and hollow. STEP is exact; STL is made of triangles, so fillets on its edges may fail.

Add, cut, keep, new object

Every solid has a Result:

  • Add joins it to the body.
  • Cut removes it from the body: pockets, slots, engraving.
  • Keep only the overlap (intersect).
  • A new object (kept apart): a separate solid. Use it for a lid and a box, or a pin through a plate.

Then click one object and use Modify › Combine to cut it from the others. Fillet, chamfer, shell and mirror act on the selected object only.


Modify: changing the body

  • Push / pull a face (U): drag a flat face in the 3D view to add or remove material.
  • Fillet / Chamfer: round or bevel edges. Choose all, top, bottom or upright edges, or click the edges in the view.
  • Shell: hollow the body with a wall thickness. The top, the bottom or the faces you click are left open. A minus wall grows outwards.
  • Split with a plane: cut the body in two. Keep both (with a gap, to print them apart), the upper or the lower part.
  • Lay flat: click a face to put it on the bed. Put it on the bed drops the lowest point to z 0.
  • Combine: the selected object cut from the others, or only their overlap kept.

Holes, screws & threads

  • Hole: click a face, then choose plain, counterbore or countersink. Depth 0 goes right through.
  • Screw hole: pick M2 to M12, then a Fit: clearance, tight, or a heat-set insert. A nut trap makes a hex pocket the size of the nut.
  • Threaded hole: a printed ISO thread with a printing clearance and a lead-in. The bolt screws straight in.
  • Hole positions are numbers: type them, or use a parameter. A pattern repeats a hole in a row, a grid or a circle.

Patterns, mirror & move

  • Pattern in a row or a grid: select a feature (a solid, a cut or a hole), then set the copies and step. Rows above 1 makes a grid.
  • Pattern round a circle: copies around a centre and axis. 360° goes all the way round.
  • Mirror: the whole body, or one feature, across the XY, XZ or YZ plane through a point.
  • Move / turn / copy (M): moves the selected object, or turns it about its centre. Copy keeps it and adds copies, each one step further. Dragging the arrows in the view makes the same step: Shift snaps, and a second drag of the same object adds to the same Move.

Parameters (names for sizes)

Click + Parameter, give it a name (wall) and a value (2), then type the name in any size field: wall, wall*2 + 1, width/2 - 8. Parameters can use other parameters. Change one value and every step that uses it updates. This is how you make a box that fits a different board by changing one number.


The feature list & undo

  • Steps are built top to bottom. A new step goes below the selected one, so select a step to insert after it.
  • reorder. switches a step off (skipped), so you can see the part without it. deletes it.
  • If a step fails it turns red with the reason, and the steps after it are greyed out. The rest of the part still shows.
  • Right-click a step to duplicate, rename or delete it.
  • Undo / Redo: the rail buttons, or Ctrl+Z / Ctrl+Y.

Measure & inspect

  • Measure (left column): size, volume, area, weight in PLA, filament length, and the centre of mass (where the part balances; keep it low and over the base for a steady print).
  • Distance between two points, or an edge's length: click two points, or one edge.
  • Section view: cut the view open across X, Y or Z to see inside. The slider moves the cut. The part itself is not changed.
  • Print check: overhangs in red, thin walls in yellow, and the weight.
  • View › Mesh quality: Draft is fast, Fine gives smooth curves for export.

Save, import, export, send

  • File › Save (Ctrl+S) writes a .mscad file with every step and parameter. Open (Ctrl+O) brings it back to edit. Your work is also kept in this browser between visits.
  • Export › STEP: the exact solid for Fusion, FreeCAD, SolidWorks or a machine shop. Export › STL: for slicers.
  • Send to › Designer: the part goes on the Designer's bed and stays editable (select it, then Edit CAD part).
    • Mechanism: use it in an assembly.
    • Paint: colour it.
    • Sculpting: as clay to shape by hand. It is then no longer a CAD part.

Keyboard shortcuts

Ctrl+Z / Ctrl+Y: undo / redo
Ctrl+S / Ctrl+O: save / open a .mscad file
Ctrl+C / Ctrl+X / Ctrl+V: copy / cut / paste shapes or steps
Ctrl+D: duplicate the shape or the selected step
On the board: S select · R rectangle · C circle · E ellipse
L outline · P polygon · O slot · T text · K rules
Enter: close an outline · Delete: remove the shape
Arrow keys: nudge the shape (Shift ×10)
In 3D: M move the selected object · U push / pull a face
W / R: arrows / rings on the selected object · Shift while dragging: snap
In a number: Arrow Up / Down step it (Shift ×10)
Esc: stop the tool, clear the selection

How-tos

A box with a lid that fits

  1. Add parameters w = 60, d = 40, wall = 2 and gap = 0.25.
  2. Make the box: a rectangle w × d, Extrude 30, then Shell it with wall (top open).
  3. Make the lid:
    • a sketch on XY with Offset 40, a rectangle w × d, Extrude 2, Result A new object;
    • then a rectangle w - 2*wall - 2*gap × d - 2*wall - 2*gap on the same plane, Extrude −4, Result A new object.
  4. Change w: the box and the lid both follow.

Four screw holes in the corners

  1. Add one Screw hole (M3), and type its position 6 mm in from a corner.
  2. Select it, then Pattern in a row or a grid: Copies 2 with a step of w - 12 along x, Rows 2 with a step of d - 12 along y.

An L-bracket with rounded edges

  1. Make a sketch On XZ (front). Draw an L with the Outline tool, and type its points exactly.
  2. Extrude it 20 with Both ways. Add Fillet 2 on the upright edges, then two screw holes.

Engraved text on a face

  1. Choose Sketch › On a face… and click the face, then add Text and type it.
  2. Extrude with Result Cut and a distance of 0.6 (or −0.6, so it goes into the part).

Tips & what CAD leaves out

  • Build the big shape first, then holes, then fillets last: fillets fail most often, and are easy to switch off.
  • Use parameters for anything that must fit: wall, clearance, screw size.
  • For a print clearance between two parts, 0.2 to 0.3 mm on each side is a good start.
  • If a step fails, read its red message. It names the step and what to change (a radius too big, a shape crossing the axis …).

Not in CAD (yet), and why:

  • Assemblies and joints: the Mechanism tab does that.
  • Sheet metal, surfaces (patches), variable fillets, drafting existing faces, patterns along a curve: rarely needed for 3D printing, and slow or unreliable in a browser.
  • Drawings with dimensions (2D prints): export STEP and make the drawing in FreeCAD or Fusion.
  • A general trim tool: shapes combine by Add / Cut out instead, and open ends can be extended or trimmed to the nearest line.